An Efficient High-Step-Up Interleaved DC–DC Converter with a Common Active Clamp

 

ABSTRACT:

This paper presents a high-efficiency and high-step up non isolated interleaved dc–dc converter with a common active clamp circuit. In the presented converter, the coupled-inductor boost converters are interleaved. A boost converter is used to clamp the voltage stresses of all the switches in the interleaved converters, caused by the leakage inductances present in the practical coupled inductors, to a low voltage level. The leakage energies of the interleaved converters are collected in a clamp capacitor and recycled to the output by the clamp boost converter. The proposed converter achieves high efficiency because of the recycling of the leakage energies, reduction of the switch voltage stress, mitigation of the output diode’s reverse recovery problem, and interleaving of the converters. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed, and its experimental results are presented for validation.

KEYWORDS

  1. Active-clamp
  2. Boost converter
  3. Coupled-inductor boost converter
  4. Dc–dc power converter
  5. High voltage gain
  6. Interleaving

 SOFTWARE: MATLAB/SIMULINK

CIRCUIT DIAGRAM:

 image001

 Fig. 1. (a) Parallel diode clamped coupled-inductor boost converter and (b) proposed interleaved coupled-inductor boost converter with single boost converter clamp (for n = 3).

 EXPECTED SIMULATION RESULTS:

 image002

Fig. 2. (a) Drain-to-source voltage of the switch in a coupled-inductor boost converter without any clamping and (b) output voltage, clamp voltage and drain to- source voltage of the switch in a coupled-inductor boost converter with the proposed active-clamp circuit.

 image003

Fig. 3. (a) From top to bottom: total input current of the converter, input currents of the interleaved coupled-inductor boost converters, and (b) primary current, secondary current, and leakage current in a phase of the interleaved coupled-inductor boost converters.

image004

Fig. 4. (a) Gate pulses to the clamp boost converter and (b) inductor current of the clamp boost converter.

image005

Fig. 5. Gate pulses to the interleaved coupled-inductor boost converters (10 V/div).

 CONCLUSION:

 Coupled-inductor boost converters can be interleaved to achieve high-step-up power conversion without extreme duty ratio operation while efficiently handling the high-input current. In a practical coupled-inductor boost converter, the switch is subjected to high voltage stress due to the leakage inductance present in the non ideal coupled inductor. The presented active clamp circuit, based on single boost converter, can successfully reduce the voltage stress of the switches close to the low-level voltage stress offered by an ideal coupled-inductor boost converter. The common clamp capacitor of this active-clamp circuit collects the leakage energies from all the coupled-inductor boost converters, and the boost converter recycles the leakage energies to the output. Detailed analysis of the operation and the performance of the proposed converter were presented in this paper. It has been found that with the switches of lower voltage rating, the recovered leakage energy, and the other benefits of an ideal coupled-inductor boost converter and interleaving, the converter can achieve high efficiency for high-step-up power conversion. A prototype of the converter was built and tested for validation of the operation and performance of the proposed converter. The experimental results agree with the analysis of the converter operation and the calculated efficiency of the converter.

 REFERENCES:

 [1] L. Solero, A. Lidozzi, and J. A. Pomilio, “Design of multiple-input power converter for hybrid vehicles,” IEEE Trans. Power Electron., vol. 20, no. 5, pp. 107–116, Sep. 2005.

[2] A. A. Ferreira, J. A. Pomilio, G. Spiazzi, and de Araujo Silva, “Energy management fuzzy logic supervisory for electric vehicle power supplies system,” IEEE Trans. Power Electron., vol. 20, no. 1, pp. 107–115, Jan. 2008.

[3] A. Emadi, K. Rajashekara, S. S. Williamson, and S. M. Lukic, “Topological overview of hybrid electric and fuel cell vehicular power system architectures and configurations,” IEEE Trans. Veh. Technol., vol. 54, no. 3, pp. 763–770, May 2007.

[4] J. Bauman and M. Kazerani, “A comparative study of fuel cell-battery, fuel cell-ultracapacitor, and fuel cell-battery-ultracapacitor vehicles,” IEEE Trans. Veh. Technol., vol. 57, no. 2, pp. 760–769, Mar. 2008.

[5] Q. Zhao and F. C. Lee, “High-efficiency, high step-up DC–DC converters,” IEEE Trans. Power Electron., vol. 18, no. 1, pp. 65–73, Jan. 2003.